diy kits transisto tester resistor transistor capacitance esr meter resistance inductance measuring npn pnp inductanc



DIY Advanced Meter Tester Kit for Capacitance ESR Inductance Resistor NPN PNP Mosfet M168 DIY Advanced Meter Tester Kit for Capacitance ESR Inductance Resistor NPN PNP Mosfet M168 Новинка

DIY Advanced Meter Tester Kit for Capacitance ESR Inductance Resistor NPN PNP Mosfet M168

1007.07 руб.
Feature: A key measurement operation auto power off delay . Shutdown current is only 20nA support battery operation. Automatic detection PNP and NPN type bipolar transistors N P -channel MOSFET JFET FET diodes two diodes thyristors resistors capacitors inductors. Automatic detection pin definitions. Measurement of the bipolar transistor current amplification factor (B) and conduction voltage emitter junction (Uf). Darlington transistor may be identified by the amplification factor of the high threshold voltage and high current. Can be detected inside the bipolar transistor and MOSFET protection diodes and displayed on the screen. The threshold voltage and the MOSFET gate capacitance measurement. Support two measuring resistors the potential can also be measured . If the potentiometer is adjusted to its end the tester can not distinguish the two ends of the pin and the middle. Resistance measurement resolution is 0.1Ohm the highest measurement value of 50MOhm. Capacitance measurement range from 25pf to 100mF (10UF). Resolution up to 1PF. Can detect more than 2UF capacitor equivalent series resistance (ESR) with a resolution of 0.01Ohm. This feature is very important for the detection capacitor performance. You can display symbols of the two diodes in the right direction also shows the forward voltage drop. LED detection of diode forward voltage drop higher than normal . Dual LED detected as double diodes. Simultaneous detection of light-emitting diodes will flash. Each test time is about two seconds only large capacitance and inductance measurements will take a long time.
MK-328 Transistor Tester Capacitor ESR Inductance Resistor Meter LCR NPN PNP MOS MK-328 Transistor Tester Capacitor ESR Inductance Resistor Meter LCR NPN PNP MOS Новинка

MK-328 Transistor Tester Capacitor ESR Inductance Resistor Meter LCR NPN PNP MOS

31.66 руб.
Description: MK-328 Transistor Tester Capacitor ESR Inductance Resistor Meter LCR NPN PNP MOS Features: 1. Using 2014 V1.11 latest version of the software, using the M328 chip, more features. German author Karl - Hans design in hardware and software compatible with the majority of fans of easy software updates escalating. 2. Using 12864 dot matrix LCD display richer content, illustrated. 3. Use a 9V battery, with battery compartment for easy battery replacement. 4. Measure the inputs have protection circuit, false positives can reduce the damage caused by the charged capacitor meter. 5. With a standard 10-pin AVR-ISP download outlets, convenience is programmed . 6. affect the accuracy of the relevant resistance using thousandth film resistors, and the remaining one percent is also used thin-film resistors. 7. The instrument has bracket for easy use. Specification: Dimensions: 83(W) x 152(height) x 34(depth)mm Weight : Host ( without battery ) approximately 200 grams Current: When 9V voltage, stable operating current of about 20mA Package includes: 1pc Transistor Tester Details pictures:
LCR-T4 Meter Tester for Capacitance ESR Inductance Resistor NPN PNP Mosfet M328 - Yellow+Multicolor LCR-T4 Meter Tester for Capacitance ESR Inductance Resistor NPN PNP Mosfet M328 - Yellow+Multicolor Новинка

LCR-T4 Meter Tester for Capacitance ESR Inductance Resistor NPN PNP Mosfet M328 - Yellow+Multicolor

1381.27 руб.
The tester is stable and easy to use which can automatically read out the accurate data and is suitable for electronic enthusiasts electronic developers designers and electronic repair. It can measure all kinds of resistance capacitance inductance two tubestransistors SCR MOS field effect tube; can determine the device type polar pin output HFEthreshold voltage the junction capacitance of the field effect tube. It is particularly suitable for transistor pairing and hybrid surface mount component identification is the best partner of amateur DIYer. Characteristics: 1.Using Atmega328 chipset stronger function. 2. Using 12864LCD diagram to display visual information content. 3.Using 6F22 9V battery to power easy and more cheaper. 4.Using active block IC testing more conveniently and quickly. 5.Liquid crystal with backlight normal testing at dark environment. 6.Pin hole sequence recognition automatically fool type testing. 7.The key device used by high precision to ensure the test precision. 8. Standby current is only 20na the standby time is long.; 9.Support late automatic calibration and ensure the accuracy. 10. Single button operation quick and convenient. Main Function:(New add function: Boot automatic detection function) 1. One key to boot one key test automatic recognition device type automatic switching range automatically shut down after the test. 2. Shutdown standby current minimum is only 20na ultra long standby the standby power consumption can be ignored and can be used in battery powered. 3. Automatic detecting the PNP and NPN type bipolar transistor N P channel MOSEFT JEFT two level pipe dual two stage tube thyristor SCR (SCR) three tubes resistors capacitors (electric discharge must be done first before measurement of capacitance) the capacitance ESR value 4. Automatic detect pin layout and given a label according to the actual sequence. 5. The threshold voltage and current measurement of bipolar transistor amplifying coefficient and the emitter junction leakage current ICE. 6 Darlington transistor can be through the high threshold voltage and high current amplification factor identification. 7. The bipolar transistor MOSFET protection and detection two tubes and the forward voltage drop Uf. 8. To detect threshold voltage VT of MOSFET and measure the gate capacitance value C. 9. Detection and transistor and MOSFET protection class two tube magnification and the determination of the base data to confirm emitter transistor the forward voltage 10. Support two resistance measurement at same time and symbol display a maximum of four digit display. The display of resistance symbol two end is the tester probe number connection (1-3). So the adjustable potentiometer can also be measured (if the potentiometer to adjust to its end the tester can not distinguish the middle and both ends of the pin) 11. The resistance measurement resolution is 0.1 ohms the highest measurement value is 50M ohms. 12. The highest four digit display-capacitor capacitance value range from 25pf (clock 8M Hz clock 50pf@1MHz) to 100mF. The resolution can reach 1pF (@8MHz clock). 13 Measure the capacitance the capacitor equivalent series resistance of the 2UF numerical above (ESR) the resolution is 0.01 ohms and display two digit numerical. 14. Display right direction signs of two two level and display the forward voltage drop. 15. LED detection is two level pipe flashes continuously several times during the testing double emitting two tubes detected as the double diode. 16. It can test the zener diode if the reverse breakdown voltage is lower than 4.5V it shows two pieces diodes and it can be confirmed by the voltage. The probe around the diode symbol is the samein this case you can identify the diode true anode by the threshold voltage at 700mV more or less! 17.It can measure the single diode reverse capacitance values. Bipolar transistor also can be measured and then must be connected with the base and collector or emitter. 18.The connection of the whole bridgerequires can be measured only one time. 19. The maximum of capacitor test is 1000000uf the best testing range is 0.2nF~7000uF if the test value is below the 25pf capacitor and a diode in parallel manner or at least 25pf shunt capacitor. After get the measured results then use it to minus parallel capacitor solute. 20. The inductance test range: 0.01mH~20H more than 20H less than 2100 ohm resistance could be identified as inductance the measurement results show only a single inductor and display the inductance value. 21. The test time is about two seconds large capacitance and inductance measurement time will be extended as the actual value. 22. Automatic shutdown after the test it has been show test results about 3 seconds then shut down. 23. It can be extended fixture after testing device this fixture needs self DIY or purchase it.
LCR-T3 Graphical Display Meter Tester for Capacitance ESR Inductance Resistor NPN PNP Mosfet M328 LCR-T3 Graphical Display Meter Tester for Capacitance ESR Inductance Resistor NPN PNP Mosfet M328 Новинка

LCR-T3 Graphical Display Meter Tester for Capacitance ESR Inductance Resistor NPN PNP Mosfet M328

1358.73 руб.
The tester is stable and easy to use which can automatically read out the accurate data and is suitable for electronic enthusiasts electronic developers designers and electronic repair. It can measure all kinds of resistance capacitance inductance two tubestransistors SCR MOS field effect tube; can determine the device type polar pin output HFEthreshold voltage the junction capacitance of the field effect tube. It is particularly suitable for transistor pairing and hybrid surface mount component identification is the best partner of amateur DIY lover. Characteristics: 1. Using Atmega328 chipset stronger function. 2. Using 12864LCD diagram to display visual information content. 3. Using 6F22 9V battery to power easy and more cheaper. 4. Using active block IC testing more conveniently and quickly. 5. Liquid crystal with backlight normal testing at dark environment. 6. Pin hole sequence recognition automatically fool type testing. 7. The key device used by high precision to ensure the test precision. 8. Standby current is only 20na the standby time is long. 9. Support late automatic calibration and ensure the accuracy. 10. Single button operation quick and convenient. Main Function: 1. One key to boot one key test automatic recognition device type automatic switching range automatically shut down after the test. 2. Shutdown standby current minimum is only 20na ultra long standby the standby power consumption can be ignored and can be used in battery powered. 3. Automatic detecting the PNP and NPN type bipolar transistor N P channel MOSEFT JEFT two level pipe dual two stage tube thyristor SCR (SCR) three tubes resistors capacitors (electric discharge must be done first before measurement of capacitance) the capacitance ESR value 4. Automatic detect pin layout and given a label according to the actual sequence. 5. The threshold voltage and current measurement of bipolar transistor amplifying coefficient and the emitter junction leakage current ICE. 6 Darlington transistor can be through the high threshold voltage and high current amplification factor identification. 7. The bipolar transistor MOSFET protection and detection two tubes and the forward voltage drop Uf. 8. To detect threshold voltage VT of MOSFET and measure the gate capacitance value C. 9. Detection and transistor and MOSFET protection class two tube magnification and the determination of the base data to confirm emitter transistor the forward voltage 10. Support two resistance measurement at same time and symbol display a maximum of four digit display. The display of resistance symbol two end is the tester probe number connection (1-3). So the adjustable potentiometer can also be measured (if the potentiometer to adjust to its end the tester can not distinguish the middle and both ends of the pin) 11. The resistance measurement resolution is 0.1 ohms the highest measurement value is 50M ohms. 12. The highest four digit display-capacitor capacitance value range from 25pf (clock 8M Hz clock 50pf@1MHz) to 100mF. The resolution can reach 1pF (@8MHz clock). 13 Measure the capacitance the capacitor equivalent series resistance of the 2UF numerical above (ESR) the resolution is 0.01 ohms and display two digit numerical. 14. Display right direction signs of two two level and display the forward voltage drop. 15. LED detection is two level pipe flashes continuously several times during the testing double emitting two tubes detected as the double diode. 16. It can test the zener diode if the reverse breakdown voltage is lower than 4.5V it shows two pieces diodes and it can be confirmed by the voltage. The probe around the diode symbol is the samein this case you can identify the diode true anode by the threshold voltage at 700mV more or less! 17.It can measure the single diode reverse capacitance values. Bipolar transistor also can be measured and then must be connected with the base and collector or emitter. 18.The connection of the whole bridge requires can be measured only one time. 19. The maximum of capacitor test is 1000000uf the best testing range is 0.2nF~7000uF if the test value is below the 25pf capacitor and a diode in parallel manner or at least 25pf shunt capacitor. After get the measured results then use it to minus parallel capacitor solute. 20. The inductance test range: 0.01mH~20H more than 20H less than 2100 ohm resistance could be identified as inductance the measurement results show only a single inductor and display the inductance value. 21. The test time is about two seconds large capacitance and inductance measurement time will be extended as the actual value. 22. Automatic shutdown after the test it has been show test results about 3 seconds then shut down. 23. It can be extended fixture after testing device this fixture needs self DIY or purchase it.
DIY Multifunction Transistor Tester Kit For LCR ESR Transistor PWM Signal Generator DIY Multifunction Transistor Tester Kit For LCR ESR Transistor PWM Signal Generator Новинка

DIY Multifunction Transistor Tester Kit For LCR ESR Transistor PWM Signal Generator

11.55 руб.
DIY Meter Tester Kit For Capacitance ESR Inductance is available now from our US warehouse Free shipping to US in 3-6 business days ship to Canada, Brazil in 7-10 days DIY Multifunction Transistor Tester Kit For LCR ESR Transistor PWM Signal Generator M328 If you need the chip of this kit: >>>>>SKU197963
LCR-T5 Transistor Meter Tester for Resistance Capacitance ESR Inductance Resistor LCR-T5 Transistor Meter Tester for Resistance Capacitance ESR Inductance Resistor Новинка

LCR-T5 Transistor Meter Tester for Resistance Capacitance ESR Inductance Resistor

2175.88 руб.
The tester is stable and easy to use which can automatically read out the accurate data and is suitable for electronic enthusiasts electronic developers designers and electronic repair. It can measure all kinds of resistance capacitance inductance diode transistors SCR MOS field effect tube; can determine the device type polar pin output HFE threshold voltage the junction capacitance of the field effect tube. It is particularly suitable for transistor pairing and hybrid surface mount component identification is the best partner of amateur DIYer. Characteristics: 1. Using Atmega328 chipset stronger function 2. Using 12864LCD diagram to display visual information content 3. Using active block IC testing more conveniently and quickly 4. LCD with backlight normal testing at dark environment 5. Pin hole sequence recognition automatically fool type testing 6. The key device used by high precision to ensure the test precision 7. Standby current is only 20na the standby time is long 8. Support late automatic calibration and ensure the accuracy. 9. Single button operation quick and convenient. Main Function: 1. One key to boot one key test automatic recognition device type automatic switching range automatically shut down after the test. 2. Standby current minimum is only 20na. 3. Automatic detecting the PNP and NPN type bipolar transistor N P channel MOSEFT JEFT two level pipe dual two stage tube thyristor SCR (SCR) three tubes resistors capacitors (electric discharge must be done first before measurement of capacitance) the capacitance ESR value 4. Automatic detect pin layout and given a label according to the actual sequence. 5. The threshold voltage and current measurement of bipolar transistor amplifying coefficient and the emitter junction leakage current ICE. 6 Darlington transistor can be through the high threshold voltage and high current amplification factor identification. 7. The bipolar transistor MOSFET protection and detection two tubes and the forward voltage drop Uf. 8. To detect threshold voltage VT of MOSFET and measure the gate capacitance value C. 9. Detection and transistor and MOSFET protection class two tube magnification and the determination of the base data to confirm emitter transistor the forward voltage 10. Support two resistance measurement at same time and symbol display a maximum of four digit display. The display of resistance symbol two end is the tester probe number connection (1-3). So the adjustable potentiometer can also be measured (if the potentiometer to adjust to its end the tester can not distinguish the middle and both ends of the pin) 11. The resistance measurement resolution is 0.1 ohms the highest measurement value is 50M ohms. 12. The highest four digit display-capacitor capacitance value range from 25pf (clock 8M Hz clock 50pf@1MHz) to 100mF. The resolution can reach 1pF (@8MHz clock). 13 Measure the capacitance the capacitor equivalent series resistance of the 2UF numerical above (ESR) the resolution is 0.01 ohms and display two digit numerical. 14. Display right direction signs of two two level and display the forward voltage drop. 15. LED detection is two level pipe flashes continuously several times during the testing double emitting two tubes detected as the double diode. 16. It can test the zener diode if the reverse breakdown voltage is lower than 4.5V it shows two pieces diodes and it can be confirmed by the voltage. The probe around the diode symbol is the samein this case you can identify the diode true anode by the threshold voltage at 700mV more or less! 17.It can measure the single diode reverse capacitance values. Bipolar transistor also can be measured and then must be connected with the base and collector or emitter. 18.The connection of the whole bridge requires can be measured only one time. 19. The maximum of capacitor test is 1000000uf the best testing range is 0.2nF~7000uF if the test value is below the 25pf capacitor and a diode in parallel manner or at least 25pf shunt capacitor. After get the measured results then use it to minus parallel capacitor solute. 20. The inductance test range: 0.01mH~20H more than 20H less than 2100 ohm resistance could be identified as inductance the measurement results show only a single inductor and display the inductance value. 21. The test time is about two seconds large capacitance and inductance measurement time will be extended as the actual value. 22. Automatic shutdown after the test it has been show test results about 3 seconds then shut down.
DIY M12864 Graphics Version Transistor Tester Kit LCR ESR PWM With Case DIY M12864 Graphics Version Transistor Tester Kit LCR ESR PWM With Case Новинка

DIY M12864 Graphics Version Transistor Tester Kit LCR ESR PWM With Case

23.29 руб.
DIY M12864 Graphics Version Transistor Tester Kit LCR ESR PWM With Case If you need the chip of this kit: >>>SKU300959
LCR-T4 12864LCD ESR SCR Meter Transistor Tester LCR-T4 12864LCD ESR SCR Meter Transistor Tester Новинка

LCR-T4 12864LCD ESR SCR Meter Transistor Tester

9.6 руб.
LCR-T4 12864LCD ESR SCR Meter Transistor Tester Features: Powered by 9V layer-built battery, can use 2 li-ion batteries to form a 8.4V battery pack for long time power. Measuring bipolar transistor current amplification factor and base-emitter threshold voltage. Automatic test the pin of a component, and display on the 128 * 64 LCD backlight. Measure the gate and gate capacitance of the MOSFET threshold voltage. One -button operation, automatic shutdown, only 20nA shutdown current. Eeverse breakdown voltage is less than 4.5V, Zener diode can be identified. 2uF more capacitors can simultaneously measure the equivalent series resistance ESR values. Via the base - emitter threshold voltage and high current amplification factor to identify Darlington transistors. Can simultaneously measure two resistors and resistor symbol is displayed. Displayed on the right with a decimal value of 4. Can detect the transistor, MOSFET protection diode amplification coefficient and the base to determine the emitter transistor forward biased voltage. Automatic detection of NPN and PNP transistors, n-channel and p-channel MOSFET, diode (including double diode) thyristor, transistor, resistor and capacitor and other components. Specifications: Material: PCB Power Mode: 6F22 Display: 128 * 64 LCD backlight Testing Speed: 2 seconds (1 minute is normal for large capacitor) Shutdown Current: 20nA Displayed Value: 25pf-100mF (resolution 1pF) Inductance: 0.01mH-20H Resistance: 2100 Power Voltage: 9V layer-built battery / 2 li-ion batteries to form a 8.4V battery pack Resolution of Resistance Measurement: 0.1 ohms The Highest Measured Value: 50M ohms Provided Testing Current: Approx. 6mA Product Size: 7.2 x 6.25cm (L * W) Package included: 1 x ESR Meter Transistor Tester

кешбака
Страницы:


The tester is stable and easy to use which can automatically read out the accurate data and is suitable for electronic enthusiasts electronic developers designers and electronic repair. It can measure all kinds of resistance capacitance inductance two tubestransistors SCR MOS field effect tube; can determine the device type polar pin output HFEthreshold voltage the junction capacitance of the field effect tube. It is particularly suitable for transistor pairing and hybrid surface mount component identification is the best partner of amateur DIYer. Characteristics: 1.Using Atmega328 chipset stronger function. 2. Using 12864LCD diagram to display visual information content. 3.Using 6F22 9V battery to power easy and more cheaper. 4.Using active block IC testing more conveniently and quickly. 5.Liquid crystal with backlight normal testing at dark environment. 6.Pin hole sequence recognition automatically fool type testing. 7.The key device used by high precision to ensure the test precision. 8. Standby current is only 20na the standby time is long.; 9.Support late automatic calibration and ensure the accuracy. 10. Single button operation quick and convenient. Main Function:(New add function: Boot automatic detection function) 1. One key to boot one key test automatic recognition device type automatic switching range automatically shut down after the test. 2. Shutdown standby current minimum is only 20na ultra long standby the standby power consumption can be ignored and can be used in battery powered. 3. Automatic detecting the PNP and NPN type bipolar transistor N P channel MOSEFT JEFT two level pipe dual two stage tube thyristor SCR (SCR) three tubes resistors capacitors (electric discharge must be done first before measurement of capacitance) the capacitance ESR value 4. Automatic detect pin layout and given a label according to the actual sequence. 5. The threshold voltage and current measurement of bipolar transistor amplifying coefficient and the emitter junction leakage current ICE. 6 Darlington transistor can be through the high threshold voltage and high current amplification factor identification. 7. The bipolar transistor MOSFET protection and detection two tubes and the forward voltage drop Uf. 8. To detect threshold voltage VT of MOSFET and measure the gate capacitance value C. 9. Detection and transistor and MOSFET protection class two tube magnification and the determination of the base data to confirm emitter transistor the forward voltage 10. Support two resistance measurement at same time and symbol display a maximum of four digit display. The display of resistance symbol two end is the tester probe number connection (1-3). So the adjustable potentiometer can also be measured (if the potentiometer to adjust to its end the tester can not distinguish the middle and both ends of the pin) 11. The resistance measurement resolution is 0.1 ohms the highest measurement value is 50M ohms. 12. The highest four digit display-capacitor capacitance value range from 25pf (clock 8M Hz clock 50pf@1MHz) to 100mF. The resolution can reach 1pF (@8MHz clock). 13 Measure the capacitance the capacitor equivalent series resistance of the 2UF numerical above (ESR) the resolution is 0.01 ohms and display two digit numerical. 14. Display right direction signs of two two level and display the forward voltage drop. 15. LED detection is two level pipe flashes continuously several times during the testing double emitting two tubes detected as the double diode. 16. It can test the zener diode if the reverse breakdown voltage is lower than 4.5V it shows two pieces diodes and it can be confirmed by the voltage. The probe around the diode symbol is the samein this case you can identify the diode true anode by the threshold voltage at 700mV more or less! 17.It can measure the single diode reverse capacitance values. Bipolar transistor also can be measured and then must be connected with the base and collector or emitter. 18.The connection of the whole bridgerequires can be measured only one time. 19. The maximum of capacitor test is 1000000uf the best testing range is 0.2nF~7000uF if the test value is below the 25pf capacitor and a diode in parallel manner or at least 25pf shunt capacitor. After get the measured results then use it to minus parallel capacitor solute. 20. The inductance test range: 0.01mH~20H more than 20H less than 2100 ohm resistance could be identified as inductance the measurement results show only a single inductor and display the inductance value. 21. The test time is about two seconds large capacitance and inductance measurement time will be extended as the actual value. 22. Automatic shutdown after the test it has been show test results about 3 seconds then shut down. 23. It can be extended fixture after testing device this fixture needs self DIY or purchase it.
купить diy kits transisto tester resistor transistor capacitance esr meter resistance inductance measuring npn pnp inductanc